Flower friendly Airrex AH-300 infrared heater solves greenhouse heating problem
Three years ago, at the Munkkivuori Garden, it was considered how the premises would be kept warm and the flowers happy. The gas heater didn’t work, but the diesel-powered Airrex AH-300 was chosen as the right heating solution. The garden has a smaller store section and a larger greenhouse. The entire space is about 5 meters wide and 30 meters long. Initially, they purchased one heater, but very quickly they bought another to the store section. The product has been very easy to use and working perfectly. Now the company has even bought a third heater. – We have been very pleased with these infrared heaters. Two of them are constantly in use and the third is used when needed. On the greenhouse side, the heat is kept at just under ten degrees Celsius and then at the store again at 13-14 degrees Celsius, says store manager Aki Lahtinen. ”Cost-wise, I can say that Airrex is much cheaper than gas heaters” The AH-300 has a charm of comfort and the flowers are happy. The device is almost odorless and produces carbon dioxide, which is great in such an environment. The 15kW / h heating output is just optimal and the low fuel consumption has brought the desired cost efficiency. Workers do not have to worry about using the equipment, just refuel and let the heater do its job. – Yes, these are easy to use, all you have to do is refuel. In terms of cost, I can say that it is much cheaper than gas-fired heaters, says Lahtinen. The Airrex AH-300 has many things that make it easy to use in such spaces. It can be easily moved and does not require a separate exhaust pipe. It is almost odorless and does not make any noise. Infrared radiation heats the material instead of the air. No fan is needed so dust or other contaminants do not rise from the floor. All in all, the Garden has been very satisfied with Airrex heaters. The thermostat-controlled heater is set at the desired temperature and then everyone can concentrate on the essentials. Read more about AH-300
Airrex AH-300 helped cut a garage’s costs significantly
Two years ago, Riku Turunen from Kontiolahti was considering the heating costs of his industrial hall. It consumed a lot of power and the bills really reflected that. Things had to change in a sensible manner. Riku’s garage hall is 135 square metres in size, and the highest point of the roof is at four metres. The large roll-up doors are prone to waste heat, so the task was a challenging one. Airrex AH-300 was selected as the heating device. AH-300 is an almost odourless, diesel-powered infrared heater with a 100% efficiency that is very well suited for industrial halls such as Turunen’s garage. Practice showed instantly that Airrex was a great solution because the device was easy to use as well as cost-efficient. “I must say that over the past two years, I’ve noticed how reliable and easy this device is to use. It’s mainly been in one place, and I’ve had no need to do anything to it although I’m using it all the time.” Besides convenience, savings are playing an important role now. “Earlier, if a period of, say, three weeks incurred an expense of a little more than €680, now I’m only spending €370, fuel included. Annually, that’s quite a big sum of money,” Turunen ponders. Once again, all that was needed was one device to solve issues. Airrex AH-300 reduced heating costs, and Riku Turunen can now focus on the essential – conducting his business – without any worries. READ MORE ABOUT AIRREX AH-300
Terrace heater, hall heater and BBQ hut heater – Airrex AH-300
Harry Mäkelä has an impressive terrace in his house. Mäkelä uses his grill a lot in winter, so the Airrex infrared heater may be switched on from Friday until Saturday. “We used to use this duct-shaped fuel oil heater. We found its flame and blast slightly dangerous in terms of heating a BBQ hut constructed of log beams with a diameter of 20 cm. A few years ago, when my son acquired an infrared heater and put it by the door of a 200-square metre maintenance hall as a kind of an air curtain, I decided to get these devices for our personal use as well. In temperatures of 20 degrees below zero, we consume around one litre of oil per hour in the BBQ hut. The 2-storey terrace is 17 metres wide and 5 metres deep. One Airrex AH-300 heater is in the lower terrace and one is upstairs. When we had to start refuelling the old heater with fuel oil, the tank of the new heater, in comparison, remains almost half-full,” Mäkelä describes his experiences. In Mäkelä’s experience, an exhaust pipe is not necessary in a big terrace or even in a BBQ hut. The heater does not emit any smoke at all because the oil burns so cleanly. Switching off the heater only causes a small fizzling sound, after which you can smell fuel oil for a while. Mäkelä, however, reckons that the consumption and odour emissions of older Airrex infrared heaters could be reduced if at least their filters were replaced. The heaters have been used for 3–4 years without requiring any particular maintenance. “I can warmly recommend these heaters to everybody, I have been very satisfied with them,” Harry Mäkelä says, summing up his experience. READ MORE ABOUT DIESEL HEATERS
Melting snow and ice with Airrex AH-800 heater
Founded in 1995, Amados Oy is specialised in the marketing and sales of machines related to construction, agriculture and property maintenance in Finland and Russia. The heater Airrex AH-800 was acquired to heat Amados’ workshop hall approximately 2.5 years ago, and it has been in heavy use ever since. Mikkeli-based Amados’ hall is 5–6 metres high and spans approximately 150 square metres, and various working machines are washed there throughout the year. At worst, half a metre of snow may pile up on top of vehicles such as wheel loaders and tractors in winter when they are driven to the hall for washing. “It only takes around three hours to deal with a large amount of snow and ice until it’s all melted away. The heater is in heavy use at that point, but it works superbly,” says Jari Ikonen from Amados. Previously, hot-air blowers were used for heating in Amados’ hall but, according to Ikonen, they were susceptible to becoming dirty. Airrex has no such issues. The diesel-powered infrared heater AH-800 is in continuous use at Amados in the cold season, and 800 litres of fuel is consumed annually. The heater is in heavy use, indeed. READ MORE ABOUT AH-800
Airrex heaters – An eco-friendly choice with renewable diesel
Airrex heaters are the perfect choice for those looking to reduce their carbon footprint without sacrificing performance. These heaters operate efficiently on both traditional diesel and fossil-free renewable diesel, ensuring 100% fuel efficiency and low fuel consumption. Summary Airrex heaters run on both traditional diesel and fossil-free renewable diesel, reducing carbon emissions. Innovative technology maximizes fuel energy use, ensuring low fuel consumption. In many cases, renewable diesel is a more eco-friendly heating option than electricity, especially in regions where power is generated from fossil fuels. Using renewable diesel for heating is a tangible step toward a fossil-free future, and Airrex heaters support this transition without compromising performance. Efficient and clean heating without emissions Airrex heaters utilize advanced fuel-efficient technology, ensuring all fuel energy is fully utilized. Their three-phase system directs infrared heat waves straight into the surrounding area. This method not only saves energy but also enables precise heat targeting with reflector structures. As a result, heating with Airrex is both economical and environmentally friendly. Renewable diesel – The environmentally friendly heating solution Diesel often gets unfairly associated with fossil fuels, yet modern diesel technology has evolved significantly, allowing for clean and efficient use of fossil-free fuels like renewable diesel. This sustainable fuel is a viable alternative for both heating and transportation, offering a significant reduction in environmental impact. Airrex heaters are at the forefront of this progress. With cutting-edge product development, Airrex heaters function seamlessly with renewable diesel, which is not always the case with conventional diesel heaters. When using renewable diesel, Airrex heaters significantly reduce emissions compared to electric heating systems—especially in countries where electricity production still relies heavily on fossil fuels. This makes renewable diesel an eco-friendly alternative with a lower environmental impact. Electricity vs. renewable diesel in heating Comparing renewable diesel to electric heating, renewable diesel is often the more sustainable choice. For example, in the EU, the average CO₂ emissions from electricity production range between 200–300 g CO₂/kWh, meaning that electric heating can have a higher carbon footprint than a fuel-burning heater using renewable diesel. Airrex heaters not only reduce dependence on fossil fuels but also offer significant energy savings. This makes them an ideal heating solution for large spaces requiring constant and efficient heating, such as garages, industrial halls, warehouses, and construction sites. A fossil-free future Reducing fossil fuel consumption is a key part of building a sustainable future. Using renewable diesel for heating is a tangible step towards a fossil-free world, and Airrex heaters make this transition easy—without compromising performance or usability. The benefits of renewable diesel extend beyond emissions. Its production supports local circular economies, as raw materials can be sourced locally, and manufacturing can be conducted regionally. This not only supports ecological goals but also benefits local economies. Airrex heaters exemplify how modern technology can drive the shift toward a more sustainable future. Airrex heaters are next-generation solutions for eco-friendly and cost-effective heating. They are the ideal choice for businesses that prioritize sustainability, efficiency, and responsibility. Discover our selection of diesel heaters today! Renewable diesel vs. biodiesel – Which is better? Renewable diesel (HVO) is technically superior to biodiesel (FAME, RME) due to: Compatibility: Works directly with existing diesel engines Better cold-weather performance Greater emission reductions More consistent fuel quality, regardless of raw materials Biodiesel is cheaper to produce but comes with technical issues and lower environmental benefits. EU regulations limit biodiesel blending in diesel fuels to 7%, whereas renewable diesel has no blend restrictions and can be used in pure form. We recommend using only renewable diesel in Airrex heaters. Biodiesel (FAME, RME) must not be used.
Cooling the Hottest Corners of Metalwork with HP-19 Mobile Air Conditioner
In the heart of any metalworking facility, heat is part of the job. Whether it’s arc welding, plasma cutting, or grinding, these tasks generate intense, localised heat, far beyond what general ventilation systems can handle. And while full-hall cooling might seem like a solution, it often proves wasteful and ineffective when the real challenge lies in just a few critical hotspots. That’s why many metal industry professionals are turning to targeted, mobile cooling, and specifically to the Rex Nordic HP-19. When General Cooling Falls Short Walk into any busy fabrication shop in summer and you’ll feel it immediately: the sharp contrast between the air near the ceiling fans and the sweltering temperatures next to a welding torch. High temperatures not only affect worker comfort and focus but also put sensitive equipment at risk. And yet, retrofitting a full AC system is costly, slow, and often unnecessary for the rest of the hall. The HP-19 approaches the problem differently. It’s not designed to cool an entire building, just the places where people and machines need it most. With a compact footprint, wheels for easy movement, and a powerful internal compressor, it delivers cold air exactly where it’s aimed – no ductwork or installation required. Cooling with Precision One of the most important features of the HP-19 is its ability to focus airflow directly at a workstation. Operators can position the unit within a few metres of a welder, plasma cutter, or CNC machine and direct the cool air precisely with built-in nozzles or optional ducting. In practice, this can lower the ambient temperature around the operator by up to 15°C – enough to make a real difference in concentration, endurance, and safety. And unlike simple fans, this unit actually conditions the air, removing heat and filtering it in the process. Built for the Realities of Industry The HP-19 isn’t a plastic consumer product. It’s built for rough environments, with a steel casing, rugged wheels, and components designed for long operating hours. It connects to a standard 230 V socket and weighs around 85 kg, heavy enough to stay put, but light enough to move when needed. Inside, it’s a 4-in-1 machine: cooling, heating, dehumidifying, and purifying the air. This means it’s useful year-round, not just in peak summer. And thanks to its built-in filters, it also reduces smoke, metal dust, and other airborne particles, particularly important in welding bays where fumes are a constant concern. Efficiency That Pays Off At 5.6 kW of cooling capacity and only 2.3 kW of power consumption, the HP-19 is surprisingly energy-efficient. It uses a low-GWP refrigerant, making it a more environmentally responsible option than many traditional systems. Combined with its focused output, that means you’re not paying to cool empty space, just the work that’s actually happening. Adaptable to Any Workshop Exhaust air can be routed out of the space using a flexible hose or simply allowed to disperse if the building is well-ventilated. This makes the HP-19 incredibly flexible. There’s no installation delay, no major changes to infrastructure, and no need to overthink where it fits. You can plug it in and start cooling in minutes. It’s a straightforward answer to a complex industrial problem. Trusted by Industrial Operators Across Europe The HP-19 is part of the new-generation range based on the long-standing Airrex HSC series, a name already well known in construction and agricultural sectors. Its larger sibling, the HP-60, offers even more power for bigger areas, but for many mid-sized workshops and welding stations, the HP-19 hits the sweet spot between performance, portability, and cost. Want to cool down your hottest workstation? Contact Rex Nordic to learn more. See how targeted mobile cooling can change the way your team works – no installation, no hassle.
Keeping stable cool: How the REX14000 keeps horses comfortable
Key benefits Cools by up to 12°C: Maintains a comfortable environment for horses. Safe and chemical-free: Utilises evaporative cooling Whisper-quiet (55 dB): Keeps the peace in animal environments. Portable and compact: Easily repositioned around stables and arenas. Improved staff comfort: A cooler environment for grooms and handlers. Field-tested performance: Larger Rex Nordic units, such as the REX25000, deliver powerful cooling and help keep horseflies at bay outdoors. Beating the heat in horse stables During hot summer days, when temperatures inside stables soar above 30°C, horses can suffer from stress and disruption to their routine. To tackle this challenge, a European stable turned to the REX14000 Air Cooler for an effective solution Understanding the challenges heat brings to stables Most stables had to contend with extreme heat during summer periods, compromising both horse welfare and performance. Conventional solutions like fans or air conditioning systems often come with drawbacks – fans merely push hot air around and require bulky equipment, while air conditioning can be costly and impractical in a stable setting. A breath of fresh air: How the REX14000 makes a difference The REX14000 was selected for its portability, lightweight design, quiet operation, and simple plug-in setup. It delivered up to a 12°C drop in temperature depending on the ambient heat. Using natural evaporative cooling with water and optional ice cubes, it provided a safe and effective cooling method for horses and handlers alike. The unit requires a steady water supply or manual refilling to operate. While it does not remove humidity from the air like a traditional air conditioner, good airflow from open windows or vents helps maintain a comfortable stable environment. Its ultra-quiet operation at just 55 dB ensured horses remained calm, while its compact design minimised disruption in busy stables. Unlike fans, which simply stir up hot air, the REX14000 creates a refreshing, cool breeze. On the ground: horses’ response and staff feedback The stable manager noticed a marked improvement in the horses’ comfort. Horses seemed more relaxed, some even lingering near the cool airflow. Training sessions became more productive, and general horse welfare improved during the hottest months. Stable staff appreciated the unit’s mobility, making it easy to move between stables, arenas, and grooming stations. They also found their working conditions much more bearable. Why the REX14000 is an essential addition for stables The REX14000 Air Cooler has proven to be a reliable and animal-friendly way to keep stables cool during the summer heat. Its quiet, effective cooling improves horse comfort and performance. Some stables in Europe have also tested the larger REX25000 models for outdoor use, achieving excellent results. These units not only provide robust cooling but also help deter horseflies, a common nuisance in fields. Horses were seen enjoying the airflow and the reduced presence of biting insects, underlining the value of REX Nordic’s air cooling solutions for both indoor and outdoor equestrian settings. This case illustrates the versatility of the REX14000, making it an ideal solution for any animal facility or workspace needing safe, efficient cooling.
Maintaining the Right Temperature in Potato Storage with a Mobile Air Conditioner
Maintaining the Right Temperature in Potato Storage with a Mobile Air Conditioner Proper storage of potatoes requires precise temperature control, as fluctuations can directly impact their quality and shelf life. For small-scale farms, the challenge is often finding a versatile and cost-effective solution that doesn’t require major upfront investment. The HP-19 mobile air conditioner from Rex Nordic offers a practical and flexible answer. Norwegian potato farmer Per Try, from Søgne, tested the HP-19 in his potato storage — and also managed to heat his workshop using the same device. Cost-Effective Temperature Control for Potato Storage Per Try faced a common problem shared by many farmers: how to maintain the ideal temperature in a potato storage space without skyrocketing energy costs. Storage temperature has a direct impact on the taste, structure, and usability of potatoes. Early potatoes store best in humid conditions between +10 and +13 °C, while regular table potatoes need cooler conditions around +4 to +6 °C. For potatoes grown specifically for French fry production, like Try’s, the optimal storage temperature is between +6 and +8 °C. Traditional storage systems relying on outdated methods or external weather conditions often fail to deliver the necessary climate controlled storage. Building a cold room in Norway can cost up to one million NOK (approximately £72,000), and the lack of flexible portable solutions limits options for small producers. Try needed an affordable and adaptable alternative — and found it in the quiet portable air conditioner unit, HP-19. Key Challenges in Potato Storage Potatoes are sensitive to storage conditions, requiring precise control of temperature, humidity, and ventilation.• Too warm → potatoes sprout and soften• Too cold → they freeze and convert starches, affecting flavor and texture➡ The HP-19 enables accurate temperature control and consistent air circulation throughout the entire storage period — ideal for reliable climate controlled storage. HP-19 in real use: Field test in Norway Try installed the HP-19 portable air conditioner unit to test its performance in cooling his potato storage. He was able to adjust the temperature precisely to +6.7 °C — the ideal setting for potatoes intended for frying. He was impressed with how quickly the unit reached the target temperature and how well it maintained that level despite varying outdoor conditions. The HP-19 also kept energy consumption low throughout the trial, offering a clear improvement over previous methods where fluctuations increased both risks and operating costs. The unit includes an effective air conditioner exhaust hose, allowing warm air to be vented out efficiently. Try redirected the exhaust heat to his workshop, giving the device a valuable second function. As summer approaches, Try expects to gain even more insights into the unit’s performance in warmer conditions. However, he already sees great potential for HP-19 — particularly for smaller-scale agricultural operations. Why HP-19 Is a Smart Choice for Agricultural Use More affordable than building a cold roomInstalling traditional cold storage is a major investment. The HP-19 offers a much more economical solution for small and medium-sized farms. Mobile and flexibleThis mobile air conditioner suits both temporary and long-term needs. It can easily be moved between spaces depending on the season or storage demand. Cooling and heating with one unitWhile it cools the storage area, the unit’s warm exhaust air can be redirected to heat another space — maximizing energy use and efficiency. Quick setup and easy to useNo permanent installation is required. The HP-19 is ready to go out of the box — perfect for urgent or seasonal storage needs. Smart control via appEquipped with Wi-Fi and air conditioner remote control via smartphone, users can monitor and adjust temperature in real-time — from anywhere. This ensures better response to changes and more stable conditions. Powerful enough for up to 550 m³The HP-19 can cool or heat spaces up to 550 cubic meters efficiently. Learn more about Rex Nordic’s HP-19 mobile air conditioner. (Need more power? Explore the HP-60 model.)
Improve productivity in Your furniture workshop with the HP-19 portable air conditioner
Maintaining comfortable working conditions in furniture production workshops is important for productivity, safety, and equipment reliability. Indoor heat, dust, chemical fumes, and limited air circulation are common issues resulting from machinery operation, sawing, sanding, and finishing processes. These conditions can cause machinery overheating, employee fatigue, lower productivity, and workplace accidents. Rex Nordic’s HP-19 portable air conditioner addresses these problems by providing effective cooling and air purification without complex installations or permanent ductwork. Typical challenges in furniture workshops Furniture manufacturing workshops often face heat, dust, and chemical emissions from woodworking machines, assembly lines, finishing materials, and daily operations. These conditions impact employee comfort and pose significant risks: Machinery Overheating: Warm temperatures and dust can cause breakdowns and shorten the lifespan of woodworking and manufacturing equipment. Employee Fatigue: Heat and poor air quality cause discomfort, reducing employee concentration and increasing accident risks Poor Air Quality: Dust, airborne particles, and chemical fumes from finishing materials negatively affect worker health. Introducing the HP-19 portable air conditioner The HP-19 from Rex Nordic is designed specifically for industrial environments. Unlike traditional fixed systems, this ductless portable air conditioner can cool specific areas or entire spaces as needed, making it suitable for furniture production facilities. Cooling and air purification capabilities The HP-19 portable air conditioner effectively reduces indoor temperatures by up to 15°C. Its built-in air purification system also filters dust, airborne particles, and chemical fumes, creating comfortable and safe working conditions: General Area Cooling: Cools large spaces up to 550 m³, quickly improving overall conditions. Targeted Spot Cooling: Equipped with a 10-meter duct to deliver precise cooling exactly where required. Air Purification: Captures and filters dust and chemical contaminants, enhancing indoor air quality and protecting employee health. Mobility and convenience The portable design allows the HP-19 to easily move between workstations or workshop areas. Its mobility ensures cooling and air purification exactly when and where needed, reducing unnecessary energy use. Energy efficiency and environmental responsibility The HP-19 delivers powerful performance with minimal energy consumption, keeping operational costs low. Additionally, it uses refrigerants with low Global Warming Potential (GWP), minimizing environmental impact: Low Energy Consumption: Saves on energy costs while supporting environmental sustainability. Eco-Friendly Refrigerants: Utilizes refrigerants with low GWP to limit environmental impact. Cost-effective Setup: Portable, ductless design avoids costly installation and maintenance. Enhancing employee comfort and safety Employee comfort directly influences productivity. The HP-19 ensures workers remain comfortable, reduces heat-related fatigue, and minimizes risks associated with dust and chemical exposure: Better Air Quality: Reduces humidity and purifies air from dust and chemical contaminants, significantly improving workplace health and safety. Simple operation and immediate use User-friendly operation is essential in busy workshops. The HP-19 portable air conditioner offers intuitive controls, quick setup, and immediate cooling and air purification. Minimal training is needed, making it accessible for all employees: Easy Controls: Quickly responds to temperature changes. Immediate Deployment: Ready for use instantly, reducing downtime. A top portable air conditioner choice in the UK With its effective cooling, air purification, portability, energy efficiency, and eco-friendly features, the HP-19 portable air conditioner is an ideal solution for industrial applications. Whether your workshop struggles with heat, dust, or chemical fumes, the HP-19 supports a comfortable, safe, and productive environment. See how the HP-19 portable air conditioner from Rex Nordic can enhance your workshop environment, improving efficiency, safety, and productivity today.
When cooling can’t compromise hygiene – Maitokolmio chose the Rex Nordic HP-60
Temperature control is a critical part of food production — not only for product safety, but also for employee working conditions. Maitokolmio, one of Finland’s most well-known dairy producers, faced a challenge in its large-scale production facilities: rising indoor temperatures were affecting both process efficiency and staff wellbeing. A trusted Finnish food industry company Maitokolmio is a 115-year-old Finnish dairy company that produces and processes milk, quark, cream, and other dairy products. The company operates two production plants in the Ostrobothnia region — one in Toholampi and another in Sievi — and is owned by local milk producers. Maitokolmio employs around 100 people. High temperatures affect productivity and product quality A lot of heat is generated in Maitokolmio’s production areas — both by the processes and the people working there. Tasks such as pasteurization and packaging significantly raise the ambient temperature. Dozens of employees work in these spaces daily, and excessive heat can impact both ergonomic conditions and the precision required in dairy processing. In food production, air conditioning systems must do more than just cool the space — they must be hygienic, reliable, and deliver clean air. “It gets very hot in the production area, and high temperatures can also affect product quality. We needed a powerful solution that would also be suitable for a food production environment,” says Anselmi Kinnunen, Maitokolmio’s Maintenance Manager. HP-60 met every requirement – Now with a HEPA filter Rex Nordic’s HP-60 air conditioning unit has been in use at Maitokolmio’s facility for about a year. The previous version of the unit proved to be a highly effective solution for cooling large dairy production spaces, and the positive experience led the company to invest in a second unit — this time, the latest model equipped with a HEPA filter. Thanks to its high cooling capacity, the HP-60 is capable of lowering the temperature across the entire production hall, even though it is primarily designed as a spot cooler. “The production hall is a large space, and we needed a device with serious cooling power. The HP-60 has fully met our expectations and clearly improved working conditions. The HEPA filter makes it especially well-suited to our type of food production,” Kinnunen notes. Quick installation – Immediate results The unit was installed quickly and required no structural changes or complex setup. Within just a few days, a noticeable drop in temperature was observed in the production space, making it easier to work through the hottest process phases. The unit has been a reliable part of daily operations from the start. HP-60 – Designed for demanding production environments The HP-60 offers significant advantages for food industry use: Powerful cooling to maintain optimal conditions, even in large production areas HEPA filter to ensure air cleanliness in hygiene-sensitive environments Dehumidification capacity up to 197 liters per day, helping prevent moisture-related issues Directed cooling, allowing airflow to be targeted exactly where it’s needed Proven solution for the confectionery industry as well The HP-60 has also proven valuable in the confectionery sector, where precise cooling and clean air are essential to sensitive manufacturing processes. Many confectionery products are made from temperature-sensitive ingredients such as chocolate, fats, and fillings that respond quickly to fluctuations in room temperature. Additionally, hygiene requirements in confectionery production are just as strict as in dairy — processes must be clean, controlled, and consistent. The HP-60’s strong cooling power, HEPA filter, and ability to deliver targeted airflow makes it an excellent choice for such environments. The unit is already in use by several companies in the industry that face similar demands for precise environmental control. A cost-effective and sustainable choice One of the key advantages of the HP-60 is its portability and significantly lower cost of implementation compared to fixed air conditioning systems. Installing a permanent solution would have required substantial investment and changes to the facility infrastructure — the HP-60 provided an immediate fix without compromises in performance or hygiene. In addition, the unit supports Maitokolmio’s commitment to sustainability — its energy-efficient operation helps reduce both emissions and operating costs.