Questions and answers

 

 

Does the heat also spread evenly in large spaces?

Yes, it does. Infrared heat spreads evenly over very long distances. Many mistakenly think that a fan is needed to transfer heat from one end of a hall to another, for example. A fan is not needed – the infrared heater heats up material, such as the wall, floor and all the materials in the space.

Why is an infrared heater more efficient than a fan heater?

The infrared heater heats material. A fan heater heats air. When you open an overhead door of a hall, for example, the warm air inside escapes, and cold air gets in. In a hall equipped with an infrared heater, all materials are warm so a lot of heat energy is retained even after the air change. In a hall equipped with a fan heater, all the heat escapes out of the door, and heating must be started over at a much lower temperature. As such, the infrared heater needs much less energy.

How can there be an odourless diesel heater?

When the fuel used is burned almost completely, it does not create odours or dangerous emissions. Carbon monoxide is formed by incomplete combustion, with too little oxygen. When combustion is complete, no carbon monoxide is formed. The product development history of Airrex goes back over 20 years, so the heater’s operation has been honed to perfection.

Why do I catch a slight smell when the heater starts/stops?

When the heater starts/stops, a mild odour of fuel may came from the exhaust pipe. This is because, upon starting/stopping, the heater does not quite manage to completely burn the fuel mist from the nozzle. The unpleasant odour is not dangerous. You can prevent any odour upon starting/stopping by using Neste Green Heat.

How can I be sure that no hazardous gases are coming out of the exhaust pipe?

The exhaust emissions of Airrex AH-300 have been studied and measured in Finland at the energy technology laboratory of Kymenlaakso University of Applied Sciences (KYAMK). Since 1992, the emission measurement laboratory at KYAMK has conducted exhaust gas measurement for power plants, the process industry and shipping companies. You can view the full measurement results here.

Why does my heater consume more than your example says?

Airrex AH-300 consumes 1.05–1.24 l per hour when running. The amount of fuel required to heat a hall, for example, is influenced by many factors: the roof and wall insulation thickness, number of doors and windows, how often doors/windows are opened, whether cold equipment is brought into the hall, etc.

During the first few days, the infrared heater consumes more fuel than normally because all the materials in the space are cold. Once the materials warm up to the desired temperature, the consumption is reduced. As such, the amount of fuel consumed per day may vary significantly.

Can Airrex AH-300 run on power from a cigarette lighter socket?

When you connect a car’s cigarette lighter socket to an inverter of at least 150 W, you can also run Airrex AH-300 on the power from the cigarette lighter. This makes it possible to use the heater in moving maintenance vehicles, for example.

Can I convey the exhaust gas outside using a pipe?

Yes, you can. Nothing prevents conveying the exhaust gas out of the heated space using a pipe.

Is it possible to get spare parts for the heater if something breaks?

Yes, it is. Every part of Airrex AH-300 heater can be replaced if needed. The importer has all the spare parts in stock, so the delivery time is very short.

I have been using the heater for a few days now. Why are there drops of water on the windows of my new hall? Does the heater release that much moisture?

Airrex infrared heater does not release enough moisture for it to condense on windows. When the infrared heater is first used in a space where only fan heaters have been used previously, there may be moisture on windows. When the infrared heater heats materials, moisture trapped in structures is effectively removed by the infrared heat. If moisture occurs when the Airrex infrared heater is used, we advise raising the temperature to approximately 20 °C for a few weeks and ensuring sufficient ventilation. This will remove the moisture from the heated space.

What installation actions are required before starting to use the new heater?

The Airrex infrared heater does not require a separate installation. Put fuel in the tank and plug in the heater, and Airrex is ready for use. The first time you use the heater, it is advisable to start it outdoors or in a well-ventilated space.

Does the heat also spread evenly in large spaces?

Yes, it does. Infrared heat spreads evenly over very long distances. Many mistakenly think that a fan is needed to transfer heat from one end of a hall to another, for example. A fan is not needed – the infrared heater heats up material, such as the wall, floor and all the materials in the space.

Why is an infrared heater more efficient than a fan heater?

The infrared heater heats material. A fan heater heats air. When you open an overhead door of a hall, for example, the warm air inside escapes, and cold air gets in. In a hall equipped with an infrared heater, all materials are warm so a lot of heat energy is retained even after the air change. In a hall equipped with a fan heater, all the heat escapes out of the door, and heating must be started over at a much lower temperature. As such, the infrared heater needs much less energy.

How can there be an odourless diesel heater?

When the fuel used is burned almost completely, it does not create odours or dangerous emissions. Carbon monoxide is formed by incomplete combustion, with too little oxygen. When combustion is complete, no carbon monoxide is formed. The product development history of Airrex goes back over 20 years, so the heater’s operation has been honed to perfection.

Why do I catch a slight smell when the heater starts/stops?

When the heater starts/stops, a mild odour of fuel may came from the exhaust pipe. This is because, upon starting/stopping, the heater does not quite manage to completely burn the fuel mist from the nozzle. The unpleasant odour is not dangerous. You can prevent any odour upon starting/stopping by using Neste Green Heat.

How can I be sure that no hazardous gases are coming out of the exhaust pipe?

The exhaust emissions of Airrex AH-300 have been studied and measured in Finland at the energy technology laboratory of Kymenlaakso University of Applied Sciences (KYAMK). Since 1992, the emission measurement laboratory at KYAMK has conducted exhaust gas measurement for power plants, the process industry and shipping companies. You can view the full measurement results here.

Why does my heater consume more than your example says?

Airrex AH-300 consumes 1.05–1.24 l per hour when running. The amount of fuel required to heat a hall, for example, is influenced by many factors: the roof and wall insulation thickness, number of doors and windows, how often doors/windows are opened, whether cold equipment is brought into the hall, etc.

During the first few days, the infrared heater consumes more fuel than normally because all the materials in the space are cold. Once the materials warm up to the desired temperature, the consumption is reduced. As such, the amount of fuel consumed per day may vary significantly.

Can Airrex AH-300 run on power from a cigarette lighter socket?

When you connect a car’s cigarette lighter socket to an inverter of at least 150 W, you can also run Airrex AH-300 on the power from the cigarette lighter. This makes it possible to use the heater in moving maintenance vehicles, for example.

Can I convey the exhaust gas outside using a pipe?

Yes, you can. Nothing prevents conveying the exhaust gas out of the heated space using a pipe.

Is it possible to get spare parts for the heater if something breaks?

Yes, it is. Every part of Airrex AH-300 heater can be replaced if needed. The importer has all the spare parts in stock, so the delivery time is very short.

I have been using the heater for a few days now. Why are there drops of water on the windows of my new hall? Does the heater release that much moisture?

Airrex infrared heater does not release enough moisture for it to condense on windows. When the infrared heater is first used in a space where only fan heaters have been used previously, there may be moisture on windows. When the infrared heater heats materials, moisture trapped in structures is effectively removed by the infrared heat. If moisture occurs when the Airrex infrared heater is used, we advise raising the temperature to approximately 20 °C for a few weeks and ensuring sufficient ventilation. This will remove the moisture from the heated space.

What installation actions are required before starting to use the new heater?

The Airrex infrared heater does not require a separate installation. Put fuel in the tank and plug in the heater, and Airrex is ready for use. The first time you use the heater, it is advisable to start it outdoors or in a well-ventilated space.

Does the heat also spread evenly in large spaces?

Yes, it does. Infrared heat spreads evenly over very long distances. Many mistakenly think that a fan is needed to transfer heat from one end of a hall to another, for example. A fan is not needed – the infrared heater heats up material, such as the wall, floor and all the materials in the space.

Why is an infrared heater more efficient than a fan heater?

The infrared heater heats material. A fan heater heats air. When you open an overhead door of a hall, for example, the warm air inside escapes, and cold air gets in. In a hall equipped with an infrared heater, all materials are warm so a lot of heat energy is retained even after the air change. In a hall equipped with a fan heater, all the heat escapes out of the door, and heating must be started over at a much lower temperature. As such, the infrared heater needs much less energy.

How can there be an odourless diesel heater?

When the fuel used is burned almost completely, it does not create odours or dangerous emissions. Carbon monoxide is formed by incomplete combustion, with too little oxygen. When combustion is complete, no carbon monoxide is formed. The product development history of Airrex goes back over 20 years, so the heater’s operation has been honed to perfection.

Why do I catch a slight smell when the heater starts/stops?

When the heater starts/stops, a mild odour of fuel may came from the exhaust pipe. This is because, upon starting/stopping, the heater does not quite manage to completely burn the fuel mist from the nozzle. The unpleasant odour is not dangerous. You can prevent any odour upon starting/stopping by using Neste Green Heat.

How can I be sure that no hazardous gases are coming out of the exhaust pipe?

The exhaust emissions of Airrex AH-300 have been studied and measured in Finland at the energy technology laboratory of Kymenlaakso University of Applied Sciences (KYAMK). Since 1992, the emission measurement laboratory at KYAMK has conducted exhaust gas measurement for power plants, the process industry and shipping companies. You can view the full measurement results here.

Why does my heater consume more than your example says?

Airrex AH-800 consumes 1.71–1.9 l per hour when running. The amount of fuel required to heat a hall, for example, is influenced by many factors: the roof and wall insulation thickness, number of doors and windows, how often doors/windows are opened, whether cold equipment is brought into the hall, etc.

During the first few days, the infrared heater consumes more fuel than normally because all the materials in the space are cold. Once the materials warm up to the desired temperature, the consumption is reduced. As such, the amount of fuel consumed per day may vary significantly.

Can Airrex AH-800 run on power from a cigarette lighter socket?

When you connect a car’s cigarette lighter socket to an inverter of at least 150 W, you can also run Airrex AH-800 on the power from the cigarette lighter. This makes it possible to use the heater in moving maintenance vehicles, for example.

Can I convey the exhaust gas outside using a pipe?

Yes, you can. Nothing prevents conveying the exhaust gas out of the heated space using a pipe.

Is it possible to get spare parts for the heater if something breaks?

Yes, it is. Every part of Airrex AH-800 heater can be replaced if needed. The importer has all the spare parts in stock, so the delivery time is very short.

I have been using the heater for a few days now. Why are there drops of water on the windows of my new hall? Does the heater release that much moisture?

Airrex infrared heater does not release enough moisture for it to condense on windows. When the infrared heater is first used in a space where only fan heaters have been used previously, there may be moisture on windows. When the infrared heater heats materials, moisture trapped in structures is effectively removed by the infrared heat. If moisture occurs when the Airrex infrared heater is used, we advise raising the temperature to approximately 20 °C for a few weeks and ensuring sufficient ventilation. This will remove the moisture from the heated space.

What installation actions are required before starting to use the new heater?

The Airrex infrared heater does not require a separate installation. Put fuel in the tank and plug in the heater, and Airrex is ready for use. The first time you use the heater, it is advisable to start it outdoors or in a well-ventilated space.